1 – Faulty Gas Valve Solenoid CoilsThese open the gas valves and let gas flow into the burner.Check if the igniter is glowing and shuts off but there is no flame.If there is no flame, the Gas Valve Solenoid Coil(s) are faulty and need to be replacedInquiry Online
2 – Blown Thermal Fuse (on blower housing or on burner assembly)The thermal fuse is most likely blown and if the thermal fuse blows, it cuts power to the burner.This is most likely caused by a clogged venting system and the heat cannot escape.Remove the Thermal Fuse and test it for continuity using a multimeter.If the Thermal Fuse has continuity, this lets you know the problem is elsewhere.If the Thermal Fuse has no continuity, it needs to be removed and replaced.Clean out the venting system for your gas dryer with a wand type vacuum cleaner and suck out all lint
3 – Faulty IgniterIgnites the gas in the burner to create a flame.If igniter fails the gas will not be ignited and the gas dryer will not heat up.Remove the Igniter and test it for continuity using a multi-meter.If the Igniter has continuity, this lets you know the problem is elsewhere.If the Igniter has no continuity, it needs to be removed and replaced
4 – Gas Supply To The DryerBe sure the gas supply line is OPEN and supplying gas to your gas dryer.Check to be sure the gas supply line is securly connected to the wall and to the dryer.If you find the gas supply line is damaged, remove and replace it
5 – Defective Flame SensorThis component detects the heat that is emitted by flame.If the Flame Sensor is faulty, the dryer will not heat.Remove the Flame Sensor and test it for continuity using a multi-meter.If Flame Sensor has continuity, this lets you know the problem is elsewhere.If the Flame Sensor has no continuity, it needs to be removed and replaced
6 – Faulty High Limit or Cycling Thermostat (Located on burner assembly)The High Limit Thermostat regulates dryer temp and shuts off the burner if the dryer overheats.The Cycling Thermostat cycles the burner ON and OFF to regulate air temperature.If either of these thermostats are faulty, the burner will not work.Remove the Thermosats and test for continuity using a multi-meter.If the Thermosats have continuity, this lets you know the problem is elsewhere.If the Thermostats have no continuity, one or both needs to be removed and replaced
7 – Faulty or Loose Wiring In Gas DryerA turned off gas valve or improperly connected gas line means no gas can get to the dryer.If any of the wiring going to any of the parts above are loose, not connected, or damaged, this will cause the gas dryer to not heat.Be sure to examine the gas dryer and check ALL wiring as sometimes it is just a simple wiring issue that is causing the dryer to not heat
NOTE: If you need to look at a DRYER REPAIR SERVICE MANUAL, they are all here. All dryer service repair manuals are for all makes of dryers. Using a service manual to understand the dryer and will help you to fix your dryer yourself
I have a LG Dlg8388nm gas dryer not getting hot.It will ignite and burn for a few seconds then shuts off and repeats that cycle.I replaced gas valve because I thought that was the cause.But no change.Done all the checks from suggestions
I have the same problem…Sears will not let me talk to a technician….can have one here due to pandemic…..all components test OK…and I even replaced coils anyway…did you ever find out what the problem was??
Kenmore elite gas dryer model 11094834201So I decided to do an extra cleaning of the lint screen, I unscrewed 3 screws that hold the lint screen compartment, there were wires connected to the moisture sensor bars, I was gentle and just laid the whole thing over inside the dryer. Then I cleaned the massive amount of lent that was down inside there. After cleaning all that I could reach I put it back together and screwed the 3 screws back in. Well! I did something???? Now the dryer won’t dry my clothes! It runs fine, starts right up as usual but won’t get hot or stay hot. It’s weird, I’ve pulled the bottom panel off and watched the igniter light the flame and after maybe 5 seconds a click happens and it shuts off. It will try to light up every few minutes but gets clicked off every time, or so I think but also sometimes I go to get laundry out….hey we’ve got 5 kids and beasts for dogs, lots of laundering:/ so yeah we are using it, but anyway sometimes it’s hot in there and the clothes are dry?????????wtheck???? Please somebody help me!!!!!
Kenmore Elite Dishwasher has a noise in the last 2:13 seconds of washing cycle. It sound like it is in the left lower side of washer. Dish washer is empty at the time of noise. I cleaned out trap and screen plus hose to disposal. I have a video of noise. Could I send it to you? I washed a cycle and it cleaned well. Just worried about continued intermittent fluttery noise
Kenmore Elite HE3 110.97892601 does not heat. I have replaced the gas coils, igniter, high temp thermostat, therafuse, and the cycling thermostat. The dryer worked for one load and again it will not heat. I noticed that the igniter does not glow and checked the surrounding wires to ensure nothing came loose… not sure what else i can do
Maytag gas washer /dryer combo(stackable) takes multiple cycles to dry clothes.drum is spinning,vent inside dryer gets holy to the touch but the clothes never seem to hardly even get warm,I clean lint trap between every load and I can actually see flame while dryer is is in use so burner seems to be working…need advice on how to repair please
This DIY "Do it Yourself" website was created by maintenance professionals and home renovating experts. We produce weekly "How To" articles with detailed step by step instructions & illustrations about fixing, organizing, recycling, repairing, renovating, removing, replacing & more. Information contained within RemoveandReplace.com is researched and backed by experienced DIY technicians. We aim to always deliver relevant and engaging content where facts and information provided is checked and rechecked for accuracy
Copyright © 2021 Bilton Mining Machinery All rights reserved. sitemap